Knowledge Base

Solved JLR “VCI Update” problem

解决安装路虎最新的驱动程序后，SDD和pathfinder软件通信不正常的问题

2. 将VNCI JLR DoIP恢复出厂设置

参考说明： https://vnciobd.com/?article/VNCI-Factory-Reset-Operation.html

3. 下载安装VNCI设备管理器，然后将设备固件升级到最新版本

VNCI设备管理器
https://ln5.sync.com/dl/cc17552a0#r4yqxaqs-iiuq2g4x-b9v8ef4n-3putav7v

4. 安装JLR VCI 设备管理器 v9.7.2798.42后，该版本不支持 SDD 和 Pathfinder 软件。

因此你需要将PDUAPI_Bosch.dll文件复制到以下路径以解决该问题：

"C:Program Files (x86)BoschVTX-VCIVCI Software (JLR)ProductsJLR-DoIPDoIP"

PDUAPI_Bosch.dll 下载地址：https://ln5.sync.com/dl/236399d50#qayjve8k-7k5fe6vj-d3qb5t85-hm5xsj67

Solved new jlr vci device manager do not support sdd and pathfinder software problem

1. Install the latest JLR VCI driver software

https://diagnosticdelivery.jlrext.com/idscentral/jlr_v9.7.2798.42_setup.exe.zip

2. Restore VNCI JLR DoIP to factory settings
Reference instructions:

https://vnciobd.com/?article/VNCI-Factory-Reset-Operation.html

3. Download and install the VNCI Device Manager, then upgrade the device firmware to the latest version VNCI Device Manager

https://ln5.sync.com/dl/cc17552a0#r4yqxaqs-iiuq2g4x-b9v8ef4n-3putav7v

4. when you installed JLR VCI device manager v9.7.2798.42, it will not be support SDD and pathfinder software

So you have to copy PDUAPI_Bosch.dll to following folder to solved the problem

“C:Program Files (x86)BoschVTX-VCIVCI Software (JLR)ProductsJLR-DoIPDoIP”

PDUAPI_Bosch.dll download address:
https://ln5.sync.com/dl/236399d50#qayjve8k-7k5fe6vj-d3qb5t85-hm5xsj67

VNCI PT3G wireless connection configuration details

Step1: Upgrade new version

you have to install newest version vnci pt3g device manager and upgrade the vnci pt3g firmware to the latest version, as shown below picture.

new version now(2024-07-04)

VNCI Device manager v2.0

firmware version: 1.0.6.3

Step2: Connect VNCI PT3G to the piwis software and switch to the USB cable wireless configuration state.

Step3: Configure the WLAN connection and AP connection network information

1. WLAN connection information configured， as shown below picture

① select "VCI configuration->WLAN Infrastructure" menu

② enter your network name and passoword

③ This check box must be checked

④ After entering all the correct configuration information, click “Update VCI” button to save the configuration information

2 . AP(Access point) connection information configured，as shown below picture

① select "VCI configuration->WLAN access point" menu

② Custom wireless network name(Default network name is “PTG_VCI_{device number}”) and password

③ This check box must be checked

④ After entering all the correct configuration information, click “Update VCI” button to save the configuration information

Step4: Pairing the current computer PIWIS3 system and VNCI PTG configuration information ( Very important! Very important! Very important! )

After the WLAN connection and AP connection configuration information are configured, you need to perform the matching operation on the PIWIS3 software of the current computer to use VNCI PT3G wireless connection on the current computer. Each time you replace the PIWIS computer, the VNCI PT3G wireless connection information must be matched again(important!!! important!!! important!!! )

As shown below picture

①select "VCI configuration->WLAN access point" menu

② Click "perform pairing now" button

③ If the pairing is successful, here is a "✔"， if the pairing is unsuccessful here is "X"

Step5: Disconnect usb port, Restart PIWIS3 software

1. Wirless connection by WLAN infranstructure

①Ensure that the current computer is connected to the network as same as the VNCI PT3G WLAN configuration network

②connect VNCI PT3G to your car or OBD16 power supply, Press and hold the VNCI PT3G button until the led light status changes, as shown bellow picture

WLAN Infranstructure connection LED light two status

③When VNCI PT3G connect to PIWIS3 software by WLAN Infranstructure , The VNCI PT3G make a deep sounds, and piwis3 software will show wireless connection icon, as shown bellow picture

1. Wirless connection by WLAN Access point connection mode

① Connect VNCI PT3G to your car or OBD16 power supply, Press and hold the VNCI PT3G button until the led light status changes, as shown bellow picture.

AP（Access point) connection LED light two status

② Enter the AP connection custom password, and after the device make a long deep sound, the PIWIS3 system will have a wireless connection icon, as shown bellow picture.

Note: The AP connection uses a wireless adapter, and when you have only one wireless adapter in your computer, you will not be able to access the Internet. If you want to connect to the Internet, you'll need an external wireless adapter.

VNCI 6154A AP connection and WALN connection configuration

AP connection configure

Default WIFI SSID : {VNCI 6154A serial number}

Default WIFI Password: 12345678

Usage method:

1. First connect the VNCI 6154A to the car or OBD16 for power supply

2. In the wireless network search box, find the VNCI 6154A WIFI SSID, enter the password and connect

Note: The AP connection uses one of your computer's wireless cards. If your computer only has one wireless card, you will not be able to access the Internet. The solution is to add an external wireless adapter

Customize the VNCI 6154A WIFI SSID and password:

1. First connect the VNCI 6154A to your computer via USB cable

2. Open your browser to access the following address: 192.168.13.69

3. Click “CONNECTIVITY->WLAN Access Point” menu and then Select “WLAN operating mode after startup”, As shown in the following picture.

4. Configure your custom WIFI SSID and password on the current page, then click Accept.

5. Select the "ADMINISTRATIOR" menu in the upper right corner, drop it to the bottom of the current page, select" Reboot System ", and click "Accept" to complete the configuration, After a successful restart, the device will make a deep sound, As shown below.

6. Disconnect the USB connection, connect the VNCI 6154A device to the car or OBD16 for 12v power, find our configured wireless information in the WIFI search box, select the custom SSID and enter the password to connect, As shown in the following picture.

WLAN connection configure

1. First connect the VNCI 6154A to your computer via USB cable

2. Open your browser to access the following address: 192.168.13.69

3. Click “CONNECTIVITY->WLAN Infrastructure” menu and then Select “WLAN operating mode after startup”, As shown in the following picture.

4. Drop down the current page to set the current WLAN SSID and password, After configuring the SSID and password and selecting the 2.4GHz communication frequency, and then click the Accept button, As shown in the following picture.

6. At this point, the VNCI 6154A device information has been added to the current WLAN "ruokewei-tp"(your WLAN), disconnect the USB cable, connect the VNCI 6154A device to your car or power the device with a 12 volt OBD16, when the VNCI 6154A make a long deep sounds, it indicate the VNCI 6154A device can be connected to any computer that using the same WLAN "ruokewei-tp"(your local area Network).

Note:

1. The frequency of the router that distributes the wireless LAN must be 2.4Ghz, and 5Ghz is not supported.

2. After you configure the AP connection and WLAN connection information, you can switch the AP connection and WLAN connection through the middle button of the device LED